TT Y-spik 20 Pro: How to Use a Y-Shaped Tent Peg in Soft Ground

What the TT Y-spik 20 Pro is designed for

The TT Y-spik 20 Pro is a lightweight aluminum peg from Tentipi’s Adventure range. Its Y-shaped profile is intended to give high stability and strength despite the low weight. According to the catalog, these pegs are used in lightweight models of Tentipi tipis in size 5 and are included in peg sets for pitching the tipi safely.

That description points to a specific job: holding a lightweight size 5 tipi in conditions where a standard peg might struggle. It is not a universal peg for every tent or every ground type. The catalog does not list load limits, so treat the Y-spik 20 Pro as one part of a complete pitching system rather than a guarantee of holding power on its own.

Catalog facts that shape how you use it

• TT Y-spik 20 Pro: TT Y-spik 20 Pro is a lightweight aluminum peg in the Adventure range, designed for high stability and strength despite low weight. Lightweight aluminum keeps pack weight down, while the Y profile is intended to add holding power in soft or loose ground.

  

• TT Y-spik 20 Pro: These pegs are used in lightweight Tentipi tipi models of size 5 and are included in peg sets for pitching the tipi safely. If you own a lightweight size 5 Tentipi, this is the peg type the catalog associates with your tent’s pitching set.
• TT Y-spik 20 Pro: Tentipi’s lightweight pegs are supplied in different quality grades with the tents, but as a spare part only the Pro version is stocked. When replacing a lost or bent peg, the Pro version is the spare-part grade Tentipi keeps available.

How to place a Y-shaped peg for better holding

The catalog does not provide a step-by-step pitching procedure, so the following is general handling advice based on the peg’s intended use. Always follow the pitching instructions supplied with your Tentipi tipi.

1. Check the ground first: The Y-spik 20 Pro is intended for lightweight size 5 tipis. Soft or loose ground is where a broad-profile peg like this is most useful; in very hard or rocky ground, a different peg type may seat more easily.
2. Match the peg to the guyline or ground point: Use the peg at the points where your tipi’s peg set calls for it. The catalog states these pegs are included in peg sets for pitching the tipi safely, so start from the layout your tent came with.
3. Drive it in at a consistent angle: Keep the peg aligned with the pull of the guyline so the Y profile resists withdrawal. The catalog does not specify an angle, so use the same angle you would for the pegs supplied with your tipi.
4. Check holding power before you rely on it: After pitching, test each peg with a firm pull. If a peg lifts easily, reset it or move it slightly. The catalog gives no load rating, so your own check is the only confirmation that the peg is seated.

When the Y-spik 20 Pro is the right peg—and when it isn’t

• Good match: lightweight size 5 Tentipi tipis: The catalog specifically names lightweight models of Tentipi tipis in size 5 as the tents these pegs are used with. If that is your tent, the Y-spik 20 Pro is the spare-part version of the peg grade Tentipi stocks.
• Good match: soft ground where you want more holding surface: The Y shape is designed for stability and strength at low weight, which is the reason to choose it over a simple lightweight peg in ground that gives way.
• Less suitable: very hard or stony ground: A lightweight aluminum peg can be harder to seat in compact or rocky ground. The catalog does not claim the Y-spik 20 Pro is suitable for every ground type, so carry a backup peg style if your route includes hard pitches.
• Less suitable: as a substitute for a full peg set: The catalog describes these pegs as part of peg sets for pitching the tipi safely. Buying one or two as spares is sensible; replacing an entire set with a single peg type is not something the catalog supports.

Replacing a lost or worn peg: what the Pro grade means

Tentipi supplies lightweight pegs in different quality grades with its tents, but as a spare part only the Pro version is stocked. That makes the TT Y-spik 20 Pro the grade to order when you need a replacement for a size 5 lightweight tipi peg set. The catalog describes the Pro version as guaranteeing long durability and reliability under demanding conditions, so it is the version Tentipi keeps for spare-part use.

The catalog price is USD 51.10, with a comparison price of USD 70.00. The peg is available in a Standard variant. The supplied information does not list a quantity per pack, dimensions, or a stated load limit, so check those details on the product page before ordering if they matter to your setup.

Spare-part details at a glance

• TT Y-spik 20 Pro: As a spare part, Tentipi stocks only the Pro version of its lightweight pegs, which the catalog describes as guaranteeing long durability and reliability under demanding conditions. If you are replacing a peg from a size 5 lightweight tipi set, the Pro grade is the one available as a standalone spare.
• TT Y-spik 20 Pro: The TT Y-spik 20 Pro is available in a Standard variant at a catalog price of USD 51.10 (comparison price USD 70.00). Price and variant are confirmed by the catalog; quantity per pack and exact dimensions are not, so verify those before purchase.